BeamClamp Components Type BY and BYP

Overview

The Type BY clamp is designed for High Friction and Tensile applications that exceed the capacities of the standard BeamClamp products. It features a recessed top that prevents the head of the bolt from rotating during installation therefore requires the use of only one wrench. The Type BYP washer can be used to fill in the recess of the Type BY to provide a flat surface for a washer and nut. This also allows the Type BY clamps to be used together in beam to beam connections. The full width tail of the BY allows for use with slotted holes for greater diversity in applications.

  • Hot Dip Galvanized to BS EN ISO 1461
  • Manufactured from Ductile Iron to BS EN 1563

The BY recess is suitable for the hexagonal head of 1/2” Grade 5 bolts, 5/8” A325/A490 bolts and 3/4” A325/A490 bolts. The Type BYP may be used to fill in the recess allowing for any grade bolt or nut to be tightened down to its surface. Typical end plate cantilevered connection supporting heavy duty pipe work.


Product FAQs

Why is the BY Clamp capable of such high frictional loads?

ANSWER: The BY Clamp has much larger sections than our standard clamps which allow it to be tightened up to much higher torques. This increases the clamping force considerably onto the steel and therefore increases the frictional slip capacity. The BY can be used grade 5 or A325 bolts and for increased frictional capacity A490 bolts and apply a higher torque.

What is the BYP used for?

ANSWER: The BYP is used to fill in the recess of the BY and convert it to a flat top clamp. This allows two BY’s to be used together and only one wrench to tighten the connection.

What is the Frictional failure mode?

ANSWER: The frictional failure mode is when the connection is measured to have moved 1mm or 0,039” from its original position. The safety factor of 2 to 1 is then applied to this load, therefore, the test load we publish is at half that of the point where the connection even moves 0.039”.

Can I use packing pieces with the BY?

ANSWER: Yes, our BF3,BF4 and BH2 packing pieces are specificall designed for use with our BY. A calculation chart is available at our resources section under “Specifying Beamclamp”, this shows what tail lengths and packing pieces are required.

Technical Specifications

Diagram - BY Clamp
Diagram - BY Clamp
Product
Code
Bolt
Grade
A Bolt Dia. B C in. D1 D2 E Width
in.
Torque
(ft/lb)
Tensile SWL (lbs)
per bolt
(5:1 Factor of Safety)
Frictional SWL (lbs)
per two bolts
Painted Steel
(2:1 Factor of Safety)
1 2
BY G12 A325/Grd.5 1/2 1-1/16 1-1/8 1/2 15/16 3/16 1/2 1-9/16 66 2383 964
BY G16 A325/Grd.5 5/8 1-5/16 1-5/16 11/16 1-3/16 5/16 9/16 1-15/16 177 3887 1803
BY G20 A325/Grd.5 3/4 1-9/16 1-1/2 7/8 1-7/16 3/8 11/16 2-3/16 346 6650 2684
BY G12 A490 1/2 1-1/16 1-1/8 1/2 15/16 3/16 1/2 1-9/16 95 2619 1771
BY G16 A490 5/8 1-5/16 1-5/16 11/16 1-3/16 5/16 9/16 1-15/16 221 4364 3485
BY G20 A490 3/4 1-9/16 1-1/2 7/8 1-7/16 3/8 11/16 2-3/16 477 7194 5341
  • Add “1” or “2” to the product code to indicate the desired tail length. For example, a 5/8” bolt diameter with 5/16” tail would be code BY1G16.
  • *Frictional failure for the Type BY Clamp is 1mm or 0.039 inches slip from its original position.
  • Frictional capacities are based on shot blast and painted steelwork.
  • Due to variance in thickness of Hot Dip Galvanized coatings please contact LNA Solutions for frictional capacities based on Hot Dip Galvanized steelwork.