Nord Lock Washer Alternative: US-Stocked Wedge Washer

Quick Answer: A Nord Lock washer is a two-piece wedge-locking washer pair that stops bolts loosening by using cam faces steeper than the thread pitch, and the LNA Wedge Washer uses the same wedge-locking principle. Mild steel Wedge Washers cover M3 to M130, the same steel size range Nord-Lock publishes, and 316L stainless covers M3 to M80. Wedge Washers are tested to ISO 16130 and DIN 25201 (Junker Test), where a pass requires holding 80% or more of the original clamp load through 2,000 cycles. LNA Solutions stocks Wedge Washers in Buffalo, NY, and will match your Nord-Lock part number to an LNA part.

Looking for a replacement for a Nord Lock washer? View Wedge Washer sizes and finishes or get a Wedge Washer quote matched to your Nord-Lock part number.

What is a Nord Lock washer and how does it work?

A Nord Lock washer is a pair of washers with cams on the inner faces and serrations on the outer faces, supplied pre-assembled. The serrations grip the bolt head, nut, and mating surface, so any loosening movement has to happen across the cam faces. Because the cam angle is steeper than the thread pitch, that movement tensions the joint instead of loosening it.

The LNA Wedge Washer works the same way. It is supplied as a pre-glued pair that installs as a single washer, and the joint can only be released by deliberate untightening.

How does the Wedge Washer compare to a Nord Lock washer?

The table places LNA’s verified Wedge Washer data beside the values Nord-Lock publishes in its own user manual. Specs measured on different scales are left out rather than forced into a comparison.

Specification LNA Wedge Washer Nord-Lock (as published by Nord-Lock)
Locking method Two-piece wedge lock, cam angle steeper than thread pitch Two-piece wedge lock, cam angle greater than thread pitch
Mild / alloy steel size range M3 to M130 M3 to M130 (#5 to 5″)
Steel material EN 1.7182 (27MnCrB5), through hardened EN 1.7182, through hardened
Steel washer hardness ≥465HV1 ≥465HV1
Steel corrosion resistance At least 1,000 hours salt spray, ISO 9227 Minimum 1,000 hours salt spray, ISO 9227
Steel temperature range -58°F to 392°F (-50°C to 200°C) -50°C to 200°C
Stainless 316L size range M3 to M80, PREN 27 M3 to M80, PREN 27
Other alloys 254SMO (PREN 45), C-276 (PREN 68), 718 (PREN 29) 254 SMO (PREN 45), C-276 (PREN 68), 718 (PREN 29)
Large OD option Yes, “LD” parts Yes, “sp” parts
Through-bolted joints Two washers, one under head, one under nut Two pairs, one under head, one under nut
Junker Test Tested to ISO 16130 and DIN 25201 Not stated in the referenced manual
US stock and engineering Stocked in Buffalo, NY, free connection design review Contact Nord-Lock

Swapping a part on a critical joint? Send your connection details to an engineer, free PE sign-off within 24 hours. Request a Wedge Washer quote: send your Nord-Lock part number, quantity, and need-by date.

What size Wedge Washer replaces my Nord Lock washer?

Match your Nord-Lock part number to the LNA part below. Diameters come from each manufacturer’s published tables, Nord-Lock in millimeters and LNA in inches.

Mild steel, zinc flake coated

Nord-Lock part Nord-Lock Øi / Øo (mm) LNA Wedge Washer part LNA Øi / Øo (in.) Bolt size
NL5 5.4 / 9.0 WW-M5 0.213 / 0.354 M5, #10
NL8 8.7 / 13.5 WW-M8 0.343 / 0.531 M8, 5/16″
NL8sp 8.7 / 16.6 WW-M8LD 0.343 / 0.653 M8, 5/16″ large OD
NL1/4″ 7.2 / 11.5 WW-1/4″ 0.284 / 0.452 1/4″
NL1/4″sp 7.2 / 13.5 WW-1/4″LD 0.284 / 0.531 1/4″ large OD
NL3/8″ 10.3 / 16.6 WW-3/8″ 0.406 / 0.653 3/8″
NL3/8″sp 10.3 / 21.0 WW-3/8″LD 0.406 / 0.826 3/8″ large OD
NL1/2″ 13.5 / 19.5 WW-1/2″ 0.532 / 0.767 1/2″
NL1/2″sp 13.5 / 25.4 WW-1/2″LD 0.532 / 1.000 1/2″ large OD
NL16 17.0 / 25.4 WW-M16 0.669 / 1.000 M16, 5/8″
NL16sp 17.0 / 30.7 WW-M16LD 0.669 / 1.208 M16, 5/8″ large OD
NL3/4″ 20.0 / 30.7 WW-3/4″ 0.787 / 1.208 3/4″
NL3/4″sp 20.0 / 39.0 WW-3/4″LD 0.787 / 1.535 3/4″ large OD
NL1″ 27.9 / 39.0 WW-1″ 1.098 / 1.535 1″
NL30 31.4 / 47.0 WW-M30 1.236 / 1.850 M30, 1-1/8″
NL36 37.4 / 55.0 WW-M36 1.473 / 2.165 M36, 1-3/8″


Stainless steel 316L

Nord-Lock part Nord-Lock Øi / Øo (mm) LNA Wedge Washer part LNA Øi / Øo (in.) Bolt size
NL5ss 5.4 / 9.0 WW-M5SS 0.213 / 0.354 M5, #10
NL8ss 8.7 / 13.5 WW-M8SS 0.343 / 0.531 M8, 5/16″
NL1/4″ss 7.2 / 11.5 WW-1/4″SS 0.283 / 0.453 1/4″
NL3/8″ss 10.3 / 16.6 WW-3/8″SS 0.406 / 0.654 3/8″
NL1/2″ss 13.5 / 19.5 WW-1/2″SS 0.531 / 0.768 1/2″
NL16ss 17.0 / 25.4 WW-M16SS 0.669 / 1.000 M16, 5/8″
NL3/4″ss 20.0 / 30.7 WW-3/4″SS 0.787 / 1.209 3/4″
NL1″ss 27.9 / 39.0 WW-1″SS 1.098 / 1.535 1″

Don’t see your size? Mild steel Wedge Washers run M3 to M130 and 316L runs M3 to M80. Send us the Nord-Lock part number and we will quote the matching Wedge Washer.

Are there stainless steel Nord Lock washer alternatives?

Yes. Wedge Washers come in 316L stainless (EN 1.4404) from M3 to M80, typically used with A4-70 or A4-80 fasteners in food and beverage, marine, chemical, and architectural work. For chloride-rich environments such as seawater, 254SMO is available, and C-276 and 718 cover acidic and high-temperature service.

What torque should I use with a wedge-locking washer?

There is no single torque value for every joint, because material strength, friction, clamp length, and embedment all change the result. The Wedge Washer technical documentation gives torque and clamp load guidelines for Grade 5, Grade 8, and Grade 9 fasteners in ft-lbs, and lubrication is recommended where possible.

Each critical bolted joint should be analyzed individually by a design engineer. Download the Wedge Washer torque guidelines or send us the joint for review.

How is a wedge-locking washer different from a spring washer?

A split or spring lock washer only adds friction under the nut or bolt head, and that friction varies from joint to joint. In Junker testing to DIN 25201, the split lock washer lost most of its clamp load and failed, while the Wedge Washer held more than 80% after material settlement.

Frequently asked questions

Where can I buy a Nord Lock washer alternative in the United States?

LNA Solutions supplies Wedge Washers from Buffalo, NY. Contact LNA at [email protected] or 1 (888) 724-2323, or request a Wedge Washer quote online with your Nord-Lock part number, quantity, and need-by date.

Are wedge-locking washers reusable?

Wedge Washers can be reused with care. Once removed, the pair separates into two pieces and must be refitted with the cam faces together and the serrated faces facing outward.

Do I need one washer or two on a bolted joint?

Fit a Wedge Washer on every side where rotation could loosen the joint. A blind connection that can only loosen one way needs one, and a through-bolted joint needs two, one under the bolt head and one under the nut.

What do “LD” and “SS” mean in Wedge Washer part numbers?

LD marks the large outside diameter version, used where Nord-Lock would specify an “sp” washer. SS marks 316L stainless steel, and SS254 marks the 254SMO grade.

How do I check a wedge-locking washer is working?

Tighten to the specified torque, mark a line across the bolt head or nut, both washer halves, and the mating surface, then untighten. If the mating-surface line stays aligned with its washer half while the bolt head or nut line separates, the washer is working.

Where should I not use a wedge-locking washer?

The serrated faces must bite into the bolt head, nut, and mating surface. On very soft surfaces such as certain plastics or polymers, correct function may not be achieved, so check suitability with our engineers.

Ready to switch to Wedge Washer?

Send your Nord-Lock part number, quantity, and need-by date, and an LNA engineer will confirm the matching Wedge Washer and quote it.

Request a Wedge Washer Quote | View Products

Nord-Lock® is a registered trademark of the Nord-Lock Group. LNA Solutions is not affiliated with or endorsed by Nord-Lock, and LNA Solutions does not sell Nord-Lock products. Nord-Lock specifications are taken from the Nord-Lock Original Washers User Manual (00095_NLO_2026_V01) and are provided for cross-reference only. Confirm critical joints with a qualified engineer.

Last reviewed: November 4, 2026

Get in Touch
structural beam clamp connections during construction